Gryke Scientific Instruments Trading

 

 

 

 

TQC-Sheen (Film Thickness)

 

 

 

 

A correct paint- or coating thickness is an important parameter in the surface treatment industry. The performance of a coating system is based upon correct application of this system following the paint manufacturers specification sheet. Each layer from primer to topcoat and individual intermediate layers are exactly specified with a minimum and maximum coating thickness.

 

 

Positest PC Powder Checker

TQC-Sheen Positest PC Powder Checker

Non-contact uncured powder thickness gauge to predict cured coating thickness
Standards: ASTM D7378
PosiTest PC Powder Checker measures uncured powder coatings using non-contact ultrasonic technology to predict a cured thickness.
The dedicated stand-alone unit is ready to measure right out of the box. The fast measurement speed is ideal for moving lines and swinging parts. Scan Mode continuously takes measurements which is ideal for analyzing large areas
For most powders no calibration adjustment is required. The PosiTest PC Powder Checker has a storage of 999 readings with onscreen averaging. Stored readings can be downloaded to PosiSoft Desktop Software.

top |back

 

 

PowderTag Thickness Analysing Gauge

TQC-Sheen PowderTag Thickness Analysing Gauge

PowderTAG uses ultraviolet techniques to measure the thickness of powder coatings in precured and cured status. Precise, reproducible and non-destructive.
Standards: DIN-EN 15042-2
• Save on powder consumption!
• Save on rework and reject!
• Improve efficiency!
• Improve quality!
PowderTAG is a non-contact production tool, developed for use at the paint-line. Because the PowderTAG’s pulse does not need to be perpendicular, and has a small measuring spot, the PowderTAG is very suitable to accurately determine the layer thickness on small, curved or hard to reach objects. Even on wire frames or small corners and edges. A LED pointer assists in determining the correct distance and location.
Due to the non-contact measuring principle parts can be tested on a slow moving line without damaging the coating. For higher line speeds it is recommended to remove the part of the line via a bypass or stop the line.

top |back

 

 

Super PIG III destructive Paint Inspection Gauge

TQC-Sheen Super PIG III destructive Paint Inspection Gauge

Standards: DIN 50986, ISO 2808
The TQC SP1100 SuperPIG is a destructive precision tool for inspection and thickness measurement on single or multiple coats on virtually all substrates, including wood, plastics, metals etc. Also observes and measures substrate and film defects. Applies a small incision in the layer of paint, and uses an integrated microscope reticle.The SP1100 is a very stable instrument, also the integrated microscope has an excellent focus. The microscope is provided with a double scale (mm and inch) which allows you to calculate to micrometers and mils. Reduce of ambient light because of a rubber end cap on the microscope so when observing through the microscope you will have a better focus upon the specimen.

Features:
• Made of Titanium anodised aluminum
• Three knife sizes and one crosscut knife in one holder
• Ergonomic design: revolving-system to change knives
• Bright white LED lights ensure clear vision through the microscope
• Small size eases use in corners
• Engraved scaling (D-factor) for easy calculations

Scope of Supply:
• Super Pig III destructive paint inspection gauge
• Black marker
• Knives 1, 2 and 4 (sp1111, SP1112, SP1116)
• Hex diagonal wrench
• Black leather case with belt clip

top |back

 

 

TQC FE|NFE Coating Thickness Gauge

TQc-Sheen TQC FE|NFE Coating Thickness Gauge

Standards: ISO 2808, ГОСТ Р 51694
This handy, robust and easy to use TQC coating thickness gauge is ideal for measurement tasks in various industries and paint applications. This compact meter allows measurement of painted objects, or other corrosion protective layer thicknesses, with accuracy measured in both Fe (iron or steel) and NFe (aluminum, copper, brass or non-magnetic steel).

Features:
• 128*128 dot matrix LCD display, standard menu operations.
• Two measure mode: single and continuous.
• Two group mode: direct (DIR) and general(GEN), readings will be lost when power off in direct mode, and not be lost in general mode. 80 readings can be stored for each group.
• Zero point calibration and multi-point calibration(up to 4 points) for each group.
• User can recall, delete specified readings, or delete group readings.
• Statistics display: mean, minimum, maximum and standard deviation.
• Three probe mode: auto, magnetic and eddy current.
• User can set high or low limit alarm for each group.
• Power off automatically.
• USB interface to data transmission.
• Low battery and error indication.

Specifications:
• Measuring principle: Magnetic induction (F-probe) and eddy current (N-probe).
• Measuring range: 0 to 1300um (0 to 51.2mils).
• Accuracy: ± (3% of readings+2um).
• ± (3% of readings+0.078mils).
• Resolution: 0um~999um (1um), 1000um~1300um (0.01mm).
• 0mils~39.39mils (0.01mils), 39.4mils~51.2mils (0.1mils).
• Calibration: One to four point calibration, zero calibration.
• Data Group: One direct group (readings not be stored to memory), four general group (readings can be stored), and each group have individual statistics, alarm settings and calibration.
• Statistics: No. of readings, mean, minimum, maximum and standard deviation.
• Units: um, mm and mils.
• Alarm: User can set the high/low alarm, and alarm icon displayed on LCD when over the limit.
• Minimum curvature radius: convex 1.5mm(59mils) and concave 25mm(984mils).
• Minimum measuring size: Diameter 6mm(236mils).
• Minimum thickness of substrate: F-probe: 0.5mm(0.02″), N-probe: 0.3mm(0.012″).
• Computer interface: Download data via USB interface.

top |back

 

 

Wet Film Thickness Gauge Stainless Steel

TQC-Sheen Wet Film Thickness Gauge Stainless Steel

Standards: ISO 2808, JIS Z2371, ГОСТ Р 51694
The TQC Wet Film Thickness Gauge WG is a hexagonal/octagonal precision measuring comb made of heavy stainless steel. The high-grade stainless steel will not be affected by acid or base elements. Models available for several different applications.
Wet Film Thickness Gauges are designed to measure the thickness of coatings immediately after they have been applied to a substrate. The gauge has a series of notches cut into its sides like the teeth on a comb. The wet film thickness of coatings including paints, resins, lacquers, varnishes and gels etc can be measured.

Use:
• Place the gauge at a 90° angle to the coated substrate
• Make sure the gauge is in firm contact with the substrate.
• Remove the gauge in a straight line up.
• Assess the teeth of the gauge. The wet film thickness lies between the largest tooth that is wet and the smallest tooth that is not wet.

top |back

 

 

Plastic Wet Film Comb

TQC-Sheen Wet Film Thickness Gauge Stainless Steel

The TQC Wet Film Comb made of plastic, to measure wet film thickness between 25 and 900µm. The TQC Wet Film Comb is designed as a disposable thickness gauge. It can be kept as a record of wet film thickness measurement for ISO or customer requirements. One side of the comb measures the wet film thickness in µm (30 steps between 25 and 900µm)., the other side measures in mills (30 steps between 1 and 35 mils)
One set TQC Wet Film Combs contains 500 pieces.

top |back

 

 

Wet Film Thickness Wheel

TQc-Sheen Wet Film Thickness Wheel

Standards: ISO 2808, JIS Z2371, ГОСТ Р 51694
Specially by TQC developed instrument for use on wet lacquers, paint and coil coated surfaces. Equipped with a precision roller-bearing for smooth rolling over the surface . The wheel has three rims, the inner rim being eccentric to the two outer rims. The outer rings are notched for a firm grip inthe surface to prevent slipping. Made of stainless steel and with an aluminum grip.

Use:

top |back

 

 

Coating Thickness Gauge PosiTector 6000

TQC-Sheen Coating Thickness Gauge PosiTector 6000

Standards: ISO 2808, ГOCT P 51694
The TQC Coating Thickness Gauge Positector 6000 from Defelsko is a rugged, fully electronic coating thickness gauge that uses magnetic and eddy current principles to measure, accurately and quickly, coating thickness on both ferrous and non-ferrous metals.

Features:
• Continually displays/updates average, standard deviation, min/max thickness and number of readings while measuring
• HiLo alarm audibly and visibly alerts when measurements exceed user-specified limits
• FAST mode—faster measurement speed for quick inspection
• USB port for fast, simple connection to a PC and to supply continuous power. USB cable included
• USB mass storage—stored readings and graphs can be accessed using universal PC/Mac web browsers or file explorers. No software required
• Every stored measurement is date and time stamped
• Software updates via web keep your gage current
• Connects to PosiTector.net
• TQC also supplies Ideal Finish Analysis software. With two user levels Ideal Finish Analysis offers user friendly reporting functions for standard production work as well as advanced calculations for in depth analysis.

The Standard models are equipped with a monochrome display and a memory for 250 measure points.
The Advanced models are equipped with a hi contrast reversible color display, onscreen help, real time graphing, picture prompting and batch notes. Memory can store 100,000 readings in up to 1000 (sub-) batches. Data transfer via USB or WiFi to a PC or via Bluetooth Wireless Technology to a PC or printer. Also available are several extra measuring modes: scan mode for continuous readings, SSPC PA2 and PSPC 90/10.
Both gauge and probe have a two year warranty.

top |back

 

 

PosiTector SmartLink

TQc-Sheen PosiTector SmartLink

PosiTector SmartLink and free mobile app turns your cell phone or tablet into a virtual PosiTector gauge
PosiTector SmartLink accepts all PosiTector 6000, RTR-H, and SPG probes easily converting to a coating thickness gage or surface profile gauge.

A Smart New Way to Measure…
PosiTector SmartLink and free mobile app turns your cell phone or tablet into a virtual PosiTector gage
• Intuitive easy-to-use touch screen operation
• Every reading is instantly transmitted to your smart device
• Tri-color LED provides immediate feedback in dark and noisy environments
• Accepts coating thickness, environmental and surface profile probes
• Lightweight and compact design—uses one AAA battery

Unprecedented Mobile Integration (no internet required)
Take full advantage of the simplicity and utility of your smart device including touch screen, keyboard, microphone, camera, email, WiFi, Bluetooth, cellular, dictation tools, and more
• Auto-pairing Bluetooth Low Energy (BLE) connection works up to 10m away (30 feet)
• Create and save professional PDF reports quickly and easily
• Add images to individual readings or batches using the camera or image library
• Annotate images using drawing tools—ideal for identifying a specific location or area within an image (included within inspection reports)
• Rename batches and add notes using the keyboard or microphone
• Real time graphing and statistical analysis with the swipe of a finger

Seamless Online Integration with an Internet Connection
Share, backup, synchronize and report measurement data via email, apps and the cloud
• AutoSync mode instantly backs up every reading to the cloud* – No account required!
• Restore data from the cloud to any smart device* – add readings, notes and images
• Live synchronization with your PosiSoft.net account*
• Share professional PDF reports and CSV data instantly via email, AirPrint™, Dropbox or other applications on your device
*Feature available on iOS devices only

top |back

 

 

Probes Ferro & Non-ferro for Positector 6000

TQc-Sheen Probes Ferro & Non-ferro for Positector 6000

Standards: ISO 2360, ISO 2808, ГОСТ Р 51694
Strong, wear resistant, ruby-tipped probes. Ferrous & Non-Ferrous probes for measuring non-magnetic coatings on a Ferrous surface or non-conductive coatings on a Non-Ferrous surface.
The different Fe/NFe probes are available in different ranges.
Standard to 1500 micron, special up to 6 mm or 13 mm.
Xtreme probe up to 10000 micron(10mm) and temperatures up to 250°C.
Separate probe available in: straight, rectangular and mini probes. (82cm cable length)*
Built-in probe available in: Straight
With the interchangeable built-in probe a gauge with integrated probe is created.
All PosiTector 6000 probes can be used with the PosiTector SmartLink; a small piece of hardware that physically connects to new and existing PosiTector probes and wirelessly connects to a free PosiTector app, turning it into a virtual PosiTector gauge. You will find the Smart Link device under ‘accessories’.
* Extra long probe cables available up to max. 75m.

top |back

 

 

Micro Probes Ferro & Non-ferro for Positector 6000

TQC-Sheen Micro Probes Ferro & Non-ferro for Positector 6000

Standards: ISO 2360, ISO 2808, ГОСТ Р 51694
Strong, wear resistant ruby tipped probes. Micro Ferrous & Non-Ferrous probes for measuring coatings on a Ferrous or Non-Ferrous surface. This small sized probes are specially developed for measurements in small areas and pipe diameters.
Fe probes have a range up to 1150 micron.
NFe probes have a range up to 625 micron.
Available as: straight 0°, angled 45° or 90°.
All PosiTector 6000 probes can be used with the PosiTector SmartLink; a small piece of hardware that physically connects to new and existing PosiTector probes and wirelessly connects to a free PosiTector app, turning it into a virtual PosiTector gage. You will find the Smartlink device under ‘accessories’.

top |back

 

 

Coating Thickness Gauge for All Substrates

TQc-Sheen Coating Thickness Gauge for All Substrates

Standards: ISO 2808, ГОСТ Р 51694
The Defelsko Positector 200 measures non-destructively a wide variety of applications using proven ultrasound technology. Measures coating thickness over wood, concrete, plastics, composites and more. Advanced models measure up to 3 individual layer thicknesses in a multi-layer system and features a graphic readout for detailed analysis of the coating system.
Conforms to ASTM D6132 and ISO 2808
All Gauges include probe, precision plastic shims, protective rubber holster with belt clip, couplant, 3 AAA batteries, instructions, nylon carrying case with shoulder strap, Certificate of Calibration traceable to NIST, two (2) year warranty

top |back

 

 

PosiTest Magnetic Pull-off Thickness Gauge

TQc-Sheen PosiTest Magnetic Pull-off Thickness Gauge

PosiTest magnetic pull-off thickness gage for the non-destructive measurement of non-magnetic coatings (paint, enamel, galvanizing, metalizing, plating, etc.) on steel.

top |back

 

 

Qnix 4200 Coating Thickness Gauge Ferro

TQC-Sheen Qnix 4200 Coating Thickness Gauge Ferro

Standards: ISO 2360, ISO 2808, ГОСТ Р 51694
Handy and robust coating thickness gauge. QNix® 4200 was developed particularly for measuring tasks in the automobile industries. This compact gauge permits extremely precise measurements of lacquer and corrosion protection thicknesses, both on steel and iron.

With the practice-oriented product properties, professionals immediately recognize the handwriting of QNix gauges:
• Extremely precise: high measuring accuracy on the entire measuring range
• Simple operation: no calibration, one button, one-hand operation
• Innovative technology: Hall-sensor and Eddy-current technology
• Broad spectrum of use: measurements on steel and iron
• Protective measuring: polished ruby tip

top |back

 

 

Qnix 4500 Coating Thickness Gauge Ferro Non-ferro

TQC-Sheen Qnix 4500 Coating Thickness Gauge Ferro Non-ferro

Standards: ISO 2360, ISO 2808, ГОСТ Р 51694
QNix® 4500 – a handy, fast and robust coating thickness gauge. QNix® 4500 was developed particularly for measuring tasks in the automobile industries. This compact gauge permits extremely precise measurements of lacquer and anti – corrosion protection coating thicknesses, both on steel and iron as well as on non-ferrous metals such as aluminum, zinc and copper. The automatic substrate recognition, extended measuring range, and increased measuring speed is what make this gauge special.

With the practice-oriented product properties, professionals immediately recognize the handwriting of QNix® gauges:
• Extremely precise: high measuring accuracy
• Simple operation: no calibration, one button, one-hand operation
• Innovative technology: Hall-sensor and Eddy-current technology
• Broad spectrum of use: measurements on steel and iron
• Protective measuring: polished ruby tip

top |back

 

 

Qnix 8500 Coating Thickness Gauge Ferro Non-ferro

TQC-Sheen Qnix 8500 Coating Thickness Gauge Ferro Non-ferro

Standards: ISO 2360, ISO 2808, ГОСТ Р 51694
QNix® 8500: A modular precision measuring system for maximum flexibility. In close collaboration with practitioners from the handwork, industry and service sectors a new generation of a modular measuring system resulted that belongs to the best of its class.
Simply place and read. Like other QNix® coating thickness gauges, the modular system of the QNix® 8500 is a perfect example of extremely simple and easy-to-use, durable and reliable gauge with variable and versatile applications. Whether on lacquer or corrosion protection on metals. Whether on iron, aluminum, copper, zinc or steel.
With a simple probe change, all non-magnetic coatings on steel and iron and all isolating coatings on non-ferrous metals are measured accurately and non-destructively
Although QNix® thickness gauges and systems are generally easy and handy, our ambition is to gain even more access to hardly reachable measuring points.
QNix® 8500 – in collaboration with the radio control probe QNix® sat – offers new applications for the measuring of coating thickness.

top |back

 

 

Ferro Probes for Qnix 8500

TQc-Sheen Ferro Probes for Qnix 8500

Standards: ISO 2808, ГОСТ Р 51694
Fe Probes to measure non-ferromagnetic coatings on ferromagnetic substrate, for example measuring on steel- or iron-substrates.
QNix® 8500 sat – a world novelty
The worldwide new, only thumb-size radio control probe allows safe precision measurements of lacquer and anti-corrosion protection coatings on metal for buildings, restorations and other safety projects – airplanes, ships or bridges.
Wireless data transfer
The transfer of data from hardly accessible measuring points per radio control offers a never known freedom of measuring coating thickness. The combination of the precision body gauge QNix® 8500 and the new, only thumb-size dual radio control probe QNix® sat is ideal, as it extends the application scope.

top |back

 

 

Ideal Finish Analysis Software

TQC-Sheen Ideal Finish Analysis Software

The Ideal Finish Analysis Software is the most advanced coating climate, coating cure and coating thickness monitoring software package available today. With two user levels Ideal Finish Analysis offers user friendly reporting functions for standard production work as well as advanced calculations for in depth analysis of the climate parameters prior to coating, the curing process and oven performance during coating and the thickness after coating. Detailed graphic representations and custom reports help you to make the right decisions to optimize your production process.
Ideal Finish Analysis is updated frequently to keep up with the latest developments in the coating and corrosion prevention industry and to comply with new Windows operating systems.

top |back

 

 

Non-ferro Probes for Qnix 8500

TQC-Sheen Non-ferro Probes for Qnix 8500

NFe Probe to measure non-ferromagnetic and electrically non-conductive coatings (insulating coatings) on non-ferromagnetic and electrically conductive substrate, for example measuring on aluminium-, zinc-, brass- and certain stainless ( high-grade ) steel-substrates.
QNix 8500 sat – a world novelty
The worldwide new, only thumb-size radio control probe allows safe precision measurements of lacquer and anti-corrosion protection coatings on metal for buildings, restorations and other safety projects – airplanes, ships or bridges.
Wireless data transfer
The transfer of data from hardly accessible measuring points per radio control offers a never known freedom of measuring coating thickness. The combination of the precision body gauge QNix® 8500 and the new, only thumb-size dual radio control probe QNix® sat is ideal, as it extends the application scope.

top |back

 

 

Ferro Non-ferro Probes for Qnix 8500

TQC-Sheen Ferro Non-ferro Probes for Qnix 8500

Standards: ISO 2808, ГОСТ Р 51694
Fe / NFe probes to measure non-ferromagnetic coatings on ferromagnetic substrate, for example measuring on steel- or iron-substrates and non-ferromagnetic and electrically non-conductive coatings (insulating coatings) on non-ferromagnetic and electrically conductive substrate, for example measuring on aluminium-, zinc-, brass- and certain stainless ( high-grade ) steel-substrates.
QNix® 8500 sat – a world novelty
The worldwide new, only thumb-size radio control probe allows safe precision measurements of lacquer and anti-corrosion protection coatings on metal for buildings, restorations and other safety projects – airplanes, ships or bridges.
Wireless data transfer
The transfer of data from hardly accessible measuring points per radio control offers a never known freedom of measuring coating thickness. The combination of the precision body gauge QNix® 8500 and the new, only thumb-size dual radio control probe QNix® sat is ideal, as it extends the application scope.

top |back

 

 

Micro Probe 500µm for Qnix 8500

TQC-Sheen Micro Probe 500µm for Qnix 8500

Standards: ISO 2808, ГОСТ Р 51694
Magnetic-inductive measurement probe with a measuring range of 0-500 µm for the most precise measurements of non-ferromagnetic coatings especially within the lower measuring range.
Designed to measure thin, non-ferromagnetic metal coatings (such as: chromium, copper, zinc, etc), lacquer, enamel or synthetic coatings on steel substrates using the magnetic-inductive measuring method, our probes deliver measurements in accordance with the DIN EN ISO 2178, ISO 2808 und ASTM B499 standards.
Thanks to the pen shaped probes, manual adjustments on measuring objects are easy to achieve and accurate. For applications demanding highest precision, we recommend mounting the probe on one of our measuring stands, available with or without additional sample holders.

top |back

 

 

Coating Thickness Calibration Standards (Certified)

TQc-Sheen Coating Thickness Calibration Standards (Certified)

Standards: ISO 2808, ГОСТ Р 51694
Coated metal calibration standards consisting of a set of 4 calibration plates with epoxy coating on steel or aluminium.
Verify the accuracy and operation of coating thickness gauges. An important component in fulfilling both ISO/QS-9000 and in-house quality control requirements. Contracts often specify that coating thickness measurements be taken by gauges whose measurement accuracy is traceable to a National Metrology Institute such as NIST or PTB.
Many QA managers find it more practical to verify the accuracy of their gauges in-house, rather than utilize TQC’s calibration services. This is especially true when many gauges are in use or when accuracy verification is performed frequently.

top |back

 

 

Calibration Standards for Coating Thickness Gauges

TQc-Sheen Calibration Standards for Coating Thickness Gauges

Standards: ISO 2808, ГОСТ Р 51694
Plastic foils and certified plastic shims. Available in the range of 12 to 20.000 micron. These foils can be applied to all ferrous- or non-ferrous metal substrates.

Non-Certified Plastic Shims
Non-Certified Plastic Shims (foils) provide a quick operational check of the instrument and they allow the user to perform practice measurements when placed over metal.
• Provide a quick operational check of the instrument by allowing the user to perform practice measurements
• Can be used to protect the probe when measuring on tacky, rough or hot surfaces
• Labeled in both Metric and Imperial units
Certified Plastic Shims
Certified Plastic Shims (foils) provide an economical alternative to coated metal plates. They have a reduced accuracy of ±2 µm (±0.08 mil). A coating thickness gage measures shim thickness when this shim is placed over a smooth metal surface (zero plate). Alternatively, they can be placed over an uncoated metal substrate. They are not suitable for use with magnetic pull-off gages.
• Each shim is packaged in their own plastic protective pouch
• Certificate of Calibration showing traceability to NIST is included with each shim or set of shims
• Certified and labeled in both Metric and Imperial units

top |back

 

 

Cross Cut Adhesion Test KIT (Master Paint Plate)

TQC-Sheen Cross Cut Adhesion Test KIT (Master Paint Plate)

Versatile measuring tool with common tests for paints and coatings.
Standards: ISO 2409, ГОСТ 15140
The TQC Cross Cut Adhesion Test KIT (Master Paint Plate) is a stainless steel measuring tool that features: a 1 mm, 1.5 mm, 2 mm and 3 mm cross cut adhesion test according NEN-EN-ISO 2409:2003 and ASTM D 3359 (X-cut) Andreas cross.

Additonal tools:
• Wet film thickness gauge ranging from 50 microns up to 160 microns.
• On the corners there is an edge grind checker for correct roundness of edges.
• At the bottom is a wet film applicator ranging from 0 to 180 µm.
• The top edge provides a leveling test, an indication of the viscosity of the coating.
Delivery includes cutting tool and tape.

Tapes for the cross cut adhesion test:
Tape For Adhesion Test according ISO 2409:2003
Tape For Adhesion Test according ISO 2409:1999 can be ordered separately as well.
Standards: NEN-EN-ISO-2409, ASTM D3359

top |back

 

 

Wet Film Measuring Comb

TQC-Sheen Wet Film Measuring Comb

Standards: ISO 2808, ГОСТ Р 51694
Rectangular promotion measuring comb with a range of 25 to 2032 µm. Made of top-quality, weather-resistant aluminum. Special printing possible with larger orders.

 

top |back

 

 

https://www.tqcsheen.com/en/